|Products In This Category:|
Headstock TIMKEN taper BEARING for Harley Davidson Forks steering neck * No outer race * - £10.25SOLD singly...( 2 required for complete build ) 1" inside diameter... Fit Harley Davidson models at least from 1960 thru to 2011 and some as early as 1949 including V-Rod models. Also fit our Hour glass Harley Springers headstock listing
Headstock bearing Cups CHR Fit Harley Davidson Bobber Cycle Haven - £26.97For Big Twin CAST type headstocks from 1960 Also Fit our machined HARLEY type Headstock listing....these have an approximate press in area outside diameter of 33.50mm These Chrome plated cups come with the bearing outer race of a 50.03mm outside diameter
Fork Boot Covers Chrome Fit 39mm Forks Harley cycle haven - £21.92Fit FXR and Sportster Models with 39mm Forks From 1988 thru 2015, Dyna 88-05
Universal Solo Seat Cycle Haven - Harley Chopper Bobber Custom Trike - £54.31Universal Solo Seats are embossed....so no leaky seat wet bum syndrome Measures 10 1/2"" Wide and 15" Long and 5" wide at the front Single 6mm thread at the Front & 2 at the Rear approx 10cm apart Ideal for Swing Arm Frames
Tail Light Cat eye IRON CROSS Harley Chopper Bobber Trike - £30.46Chrome Cats Eye Tail light Stop &Tail...RED bulb for the clear iron cross lens Mounts by two 1/4" studs @ 2" centres Chrome plated die cast alloy with eye catching fluted body measures 5" x 2 1/2"
JayBrake trans end cover 87 - 06 ( Except 06 Dyna ) with site glass - £400.00Allows at a glance your oil level die cast alloy and polished ( cable opperated ) and will except hydraulic conversion.
"O" Rings for TWIN CAM often used when Servicing Harley Davidson type models - £6.20Ideal for any profesional workshop to have on hand for on the spot repairs ( saves the expense of having numerous packs of 10 ) or just for do it yourself home servicing
16" Black Ape Hanger 1" Bars Fits 82up Harley Chop Bobber Custom. Cycle Haven - £48.46Made with dimples for wiring, with approximate dimensions of 35" width... 7 " pull-back... 7" riser clamp area width use ( Not knurled )
16" Ape Hanger install Kit for Harley Davidson SPORTSTER models 96-03 with a 7/16" banjo bolt into master/c at 90 degree angle - £212.46May be suitable for other models & years. Please check content info against your requirements. Includes Throttle : Idle & Clutch cables & brake hose & wiring extensions
22mm ( 13/16" Harley Davidson type ) KIT includes Gas Tap & Weld in threaded bung... Straight Down outlet for 1/4" I.D. fuel pipe. - £44.89Comes with steel 22mm x 1mm ( 13/16" ) weld in bung external thread and a gas tap nut machined again to fit after the chroming process had made it oversize
Large Solo Seat - Cycle Haven- Harley Chopper Bobber Custom Trike..... 6cm Thick we also have this in 4cm Thick.. please state which thickness - £51.07Large Plain Solo Seat in Black Measures 340mm Wide and 300mm Long Steel base with studs, with approximately a 2.5" radius frontal area. mounting studs 7 1/4" wide
10" Flat Fender Raw Steel RUSTY Harley Bobber Chopper Trike Cycle Haven.... - £101.44So called 10" Flat Steel Fender The width varies a bit...so say around about 9 15/16" to 10 1/16 on the inside and may vary from to end with a 1.7mm wall thickness.. THESE are Available to order. Last updated 11/18
Deluxe Locking Gas Cap Set Screw in Vented Harley Chop - £71.00"Classic Style" ( 1 x Vented & 1 x None Vented ) Has a special lock-cover which will prevent water to enter the tank through the key hole Fits Harley Davidson model & custom tanks 82 up For SCREW in Gas Tanks ONLY Supplied with 2 Keys
Locking Gas Cap Screw in Vented Harley Chop Bob - £22.07Locking Screw in Chrome Gas Cap 1 x Vented Right Side or single cap tanks Fits Harley Davidson model & custom tanks 82 up For SCREW in Gas Tanks ONLY Supplied with 2 Keys
Gas Cap Screw in None Vented Harley Chop Bobber 83-95 - £14.44Chrome Gas Cap ( 1 x None Vented ) Left Side Fits SCREW in Gas Tanks ONLY From 1982-95