ALL Custom - All Listings



Categories:
  • Previous
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 15
  • Next
  • Products In This Category:
    1/8

    1/8" BSP Blanking plug for Harley & Custom gas / petrol tanks - £3.49

    Made from Brass & NICKEL plated ...clean low profile Allen key head, with built in captive seal.

    Quantity:  at  £3.49  each

    ...More Information

    1/8

    1/8" NPT drain plug for oil tanks & blanking petrol tanks on Harley Davidson parts - £13.51

    1/8"-27 NPT threaded; Hex head Fits: > Fork slider drain plug: 49-E77 FL(NU) Crankcase drain plug: 77-18 XL; 08-12(NU)XR1200 (2 used) Transmission: 01-16 Dyna, FLT Oil pump: 68-99 B.T. Oil tank & transm.: 00-16 Softail Primary: 79-84(NU)FLT; 82-84(NU)FXR

    Quantity:  at  £13.51  each

    ...More Information

    1/8

    1/8" NPT Threaded Red Handle Gas Tap on off 90' for 1/4" I.D. fuel pipe. - £41.46

    Quantity:  at  £41.46  each

    ...More Information

    10

    10" Ape Hanger Bars 7/8" Chrome Custom Chop Bob Cycle Haven - £34.64

    Chrome 10" Rise Ape hanger Bars Fits 7/8" Controls Will Fit any Custom, Chopper, Bobber or Trike with 7/8" Bars 33" wide, 7 1/2" center width

    Quantity:  at  £34.64  each

    ...More Information

    10" Ape Hanger KNURLED with HIDDEN WIRING in CHROME for Harley Davidson or Custom - £44.76

    Pre-drilled 1/2" hole size at grip end & 3/8"x1.5" slot at the centre for hidden wiring. Will Fit any Custom, Chopper, Bobber or Trike with 1" Bars Approx 32.5" wide 7 " pull-back 7.5" max riser clamp use width & 4.5" Knurled width

    Quantity:  at  £44.76  each

    As we can obtain these pretty much overnight.....just place your order and we shall get you supplied...pronto

    ...More Information

    12mm Marine grade 316 Stainless Steel Engine mounting bolt / stud ( CH127 for our CB750 framework ) OR MADE TO ORDER Chopper Bobber

    12mm Marine grade 316 Stainless Steel Engine mounting bolt / stud ( CH127 for our CB750 framework ) OR MADE TO ORDER Chopper Bobber - £13.87

    272mm unthreaded central area ( to prevent damage to the engine casting & mounting plates ( 301mm total length ) For other lengths & diameters, send us details

    Quantity:  at  £13.87  each

    ...More Information

    16

    16" Apes Chrome Handle Bars 7/8" Custom Chopper Bobber Cycle Haven - £58.27

    16" Ape Hangers 7/8" diameter Excellent Quality chromed steel tubing

    Quantity:  at  £58.27  each

    ...More Information

    16

    16" REAR wheel Custom Chrome to replace a Harley Davidson 3.00 to 3.50 Custom Hub - £344.87

    Custom 3.50 width deep chrome plated 40 spoke wheel 3/4" axle ( can be sleeved to 1" ) sealed inside rim over spokes nipples. 7/16 & 3/8" UNC

    Quantity:  at  £344.87  each

    ...More Information

    17mm Axle Reducers ( 1 pair ) for our 20mm axle plates

    17mm Axle Reducers ( 1 pair ) for our 20mm axle plates - £39.38

    Made from stainless steel

    Quantity:  at  £39.38  each

    ...More Information

    1982- 95 Black Locking Gas Cap Screw in Vented for Harley Davidson

    1982- 95 Black Locking Gas Cap Screw in Vented for Harley Davidson - £18.38

    Quantity:  at  £18.38  each

    ...More Information

    1983 - 95 Black Gas Cap Set Screw In to Fit Harly Davidson

    1983 - 95 Black Gas Cap Set Screw In to Fit Harly Davidson - £28.75

    1 x Right + 1 x Left Fits Screw in Gas Tanks

    Quantity:  at  £28.75  each

    ...More Information

    2 x Bearings & Outer Races for Headstock *GENUINE TIMKEN* for Harley Davidson forks Bobber Choppers Cycle Haven

    2 x Bearings & Outer Races for Headstock *GENUINE TIMKEN* for Harley Davidson forks Bobber Choppers Cycle Haven - £37.34

    2 x bearings & 2 x outer races (Order 1 for complete build..content as photo) Fit Harley models at least from 1960 thru to 2011 and some as early as 1949 Using 1" inside diameter bearings & inside diameter bearings & 50.30mm outside diameter races

    Quantity:  at  £37.34  each

    ...More Information

    2

    2" Black Seat Springs 1 pair Cycle Haven - £11.99

    Quantity:  at  £11.99  each

    ...More Information

    2

    2" Chrome Seat Springs 1 pair Cycle Haven - £13.99

    Quantity:  at  £13.99  each

    ...More Information

    2

    2" Copper Finish Seat Springs 1pr cycle haven - £14.62

    Quantity:  at  £14.62  each

    ...More Information

    22mm  ( 13/16

    22mm ( 13/16" ) RIGHT outlet for 1/4" I.D. fuel pipe. Gas Tap Chrome ( 13/16" Harley Davidson type) Chopper - Bobber - Custom -Trike - £19.92

    Fits 1975 up Harley Tanks with 22mm x 1mm ( 13/16" ) external thread. Comes with nut & 90 degree RIGHT outlet with a reserve

    Quantity:  at  £19.92  each

    ...More Information

    22mm ( 13/16

    22mm ( 13/16" ) DOWNWARD outlet for 1/4" I.D. fuel pipe. Gas Tap Chrome Harley Custom Bobber - £20.04

    Quantity:  at  £20.04  each

    ...More Information

    22mm ( 13/16

    22mm ( 13/16" ) LEFT outlet Gas Tap Chrome ( 13/16" Harley Davidson ) Chopper - Bobber - Custom - Trike Cycle Haven - £21.96

    Fits 1975 up Harley Tanks with 22mm x 1mm ( 13/16" ) external thread. Comes with nut & 90 degree LEFT outlet with a reserve

    Quantity:  at  £21.96  each

    ...More Information

    22mm ( 13/16

    22mm ( 13/16" ) Weld in Bung threaded for gas tap / petcock to fit ONLY GENUINE Harley Davidson taps - £13.92

    Fits GENUINE Harley taps... some custom aftermarket may require a 22mm x 1mm machine tap running through to clear the chrome plating build up.

    Quantity:  at  £13.92  each

    ...More Information

    22mm (13/16

    22mm (13/16") Rebuild Kit for Petcocks for Harley Taps - £8.57

    Quantity:  at  £8.57  each

    As we can obtain these pretty much overnight.....just place your order and we shall get you supplied...pronto

    ...More Information


    Back to Top

  • Previous
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 15
  • Next